Wanted: ****WANTED***21p PROP***WANTED****

[darklordhill]

****WANTED***WANTED***WANTED****
stainless steel Propeller 13 x 21p, to fit a Mercury outboard with a 4 1/4 (4.25) gearcase.

[Jeff]

Originally Posted by darklordhill

****WANTED***WANTED***WANTED****
stainless steel Propeller 13 x 21p, to fit a Mercury outboard with a 4 1/4 (4.25) gearcase.

I've a new mercury 21" laser II Inc Flo-torq hub kit for sale in the 'list your props' in the engine and props section on here :-)

Part Number 48-16546A46
13 7/8" Dia x 21" 3RH SS

New (1 hr use) Mercury Laser II 21" RH
Only used for an hour as a test - as new. Box and Flo-torq 11 hub kit included
£200 delivered UK Mainland

Jeff
07771 795 137

[phantom 19]

If it is a 21" laser2 it will not be 4 1/4" gearcase.

[darklordhill]

Originally Posted by Jeff

I've a new mercury 21" laser II Inc Flo-torq hub kit for sale in the 'list your props' in the engine and props section on here :-)

Part Number 48-16546A46
13 7/8" Dia x 21" 3RH SS

New (1 hr use) Mercury Laser II 21" RH
Only used for an hour as a test - as new. Box and Flo-torq 11 hub kit included
£200 delivered UK Mainland

Jeff
07771 795 137

Thanks anyway Jeff
But as Phantom has said it's probably not for a 4 1/4 gearcase, more likely 4 3/4.

[Jeff]

Originally Posted by phantom 19

If it is a 21" laser2 it will not be 4 1/4" gearcase.

Will this not be the correct fit ??
From the Mercury Website
Laser II
Outstrip the Competition
The original choice for outboard-powered bass boats under 200hp.
Available pitches 19, 20, 21, 22, 23, 24, 25, 26
Rotation LH, RH
Performance vent system (PVS) No
Boat types Bass, Deckboat, Inshore Fishing
Number of blades 3
Material Stainless Steel
Fits Outboards 75hp - 125hp
Recommended for 75hp - 115hp aluminum deep-V boats, Outboard-powered bass boats less than 200hp


The diameter of the inner shoulder at the gearbox end of the prop is 4 1/4" and the outside diameter is 4 1/2"


Photos attached show the shoulder dims, spec and condition
It also comes with the uprated Flo-torq 11 hub with the rear bushing

I am sure someone will tell me if I am wrong :-)

[darklordhill]

Originally Posted by Jeff

Will this not be the correct fit ??
From the Mercury Website
Laser II
Outstrip the Competition
The original choice for outboard-powered bass boats under 200hp.
Available pitches 19, 20, 21, 22, 23, 24, 25, 26
Rotation LH, RH
Performance vent system (PVS) No
Boat types Bass, Deckboat, Inshore Fishing
Number of blades 3
Material Stainless Steel
Fits Outboards 75hp - 125hp
Recommended for 75hp - 115hp aluminum deep-V boats, Outboard-powered bass boats less than 200hp


The diameter of the inner shoulder at the gearbox end of the prop is 4 1/4" and the outside diameter is 4 1/2"


Photos attached show the shoulder dims, spec and condition
It also comes with the uprated Flo-torq 11 hub with the rear bushing

I am sure someone will tell me if I am wrong :-)

Well it looks like it will fit Jeff

[darklordhill]

Where did this info come from Jeff
( Fits Outboards 75hp - 125hp
Recommended for 75hp - 115hp aluminum deep-V boats, Outboard-powered bass boats less than 200hp )

As the info in the pic on the box says different ?

Lee

[Jeff]

Originally Posted by darklordhill

Where did this info come from Jeff
( Fits Outboards 75hp - 125hp
Recommended for 75hp - 115hp aluminum deep-V boats, Outboard-powered bass boats less than 200hp )

As the info in the pic on the box says different ?

Lee

It came from the Mercury website but this may be newer information ans sizing. The earlier ones were large gearcase in odd pitches and 'small' gearcase even pitches.

The measurements of the prop diameter are accurate as you can see but it is confusing. This was for a mercury Optimax 150 originally

[darklordhill]

i've just measured my props and they are just under 4" at the at the point yours is 4 1/4. so yours must be for the bigger gearcase

[Jeff]

Originally Posted by darklordhill

i've just measured my props and they are just under 4" at the at the point yours is 4 1/4. so yours must be for the bigger gearcase

Thanks for letting me know.

E Bay next - but now I know the difference :-)

[diver 1]

If its 13 spline shaft then I have a 13x19 stainless prop you could have for £65. Its practically brand new - don't think its ever been wet!