BananaShark 34' Build thread - Page 10

Zippy · 01 June 2011, 08:46

dont know if i am being blind but are you not running with trim tabs??

looking great! cant wait to see this on the water!!

Cookee · 01 June 2011, 11:03

Quote:

Originally Posted by Zippy

dont know if i am being blind but are you not running with trim tabs??

looking great! cant wait to see this on the water!!

The steering rams interfere with the tabs we have so we're trying it without first - or a bow tank - we may add either or both at a later stage.

Mollers · 01 June 2011, 11:04

Cookee, a bit of flocking would look good on the interior.

Autoflock.co.uk - Flocking
It's been used on rally car dashes for a while now. A lad I know is providing a flocking service.

Zippy · 01 June 2011, 11:20

interesting! i guess you have no trim adjustment on the surface drives?

gonna look great when its on the water. what are you doing with the wrapping? should look really smart!

have you got a sponsor lined up yet??

Black · 01 June 2011, 12:31

Cookee - looks awesome

I'm down in Salcombe from this Friday evening for a week, is your new boat going to be seen on the water?

Cookee · 01 June 2011, 12:37

Mollers - Helpful as always!

Zippy - if you look there are four rams - two for steering and two for trimming the drives! Always room for more sponsorship! The fourth seat will be avaialable to anyone who can bring in some money to pay for entry fees and fuel costs - fuel will be cheap @ only 104lph flat out for both motors!

Black - You're welcome during opening hours at the workshop in Churchstow (9.30 to 5.30) (07836 268747) and unless we have a lot more unforeseen issues we will definitely be out before the end of next week - big wedding to go to on Saturday at Cliff House first though!

Black · 01 June 2011, 12:43

Cookee, assuming I can loose the kids somewhere I'll be up to say hello.

Do you launch from Batson with the crane?

Jizm · 01 June 2011, 12:50

Looks awesome cookee, looking for ward to seeing it in the flesh...

Cookee · 01 June 2011, 13:52

Quote:

Originally Posted by Black

Cookee, assuming I can loose the kids somewhere I'll be up to say hello.

Do you launch from Batson with the crane?

We have a trailer for the slip - just hope it will get over the hump as it's a bit long!

Mollers · 01 June 2011, 16:16

Who's driving the B/shark Facebook site? They're keeping that a humour free zone.

martini · 01 June 2011, 16:37

Quote:

Originally Posted by Mollers

Who's driving the B/shark Facebook site? They're keeping that a humour free zone.

I recently suggested it might be a struggle to fit a blue rizla between the motors but nobody was biting

Mollers · 01 June 2011, 16:49

Quote:

Originally Posted by martini

I recently suggested it might be a struggle to fit a blue rizla between the motors but nobody was biting

My 'Lash-up' comment wasn't at all well received. 'As if..'

martini · 01 June 2011, 16:57

Quote:

Originally Posted by Mollers

My 'Lash-up' comment wasn't at all well received. 'As if..'

Found ya

Black · 01 June 2011, 17:52

cookee - love to see that going down the slip, I've got the parking slot behind the dinghy rack for the week, so great viewing platform

Looking forward to

Hugh Jardon · 01 June 2011, 18:25

Chav!

Quote:

Originally Posted by Mollers

Cookee, a bit of flocking would look good on the interior.

Autoflock.co.uk - Flocking
It's been used on rally car dashes for a while now. A lad I know is providing a flocking service.

Mollers · 01 June 2011, 18:26

Quote:

Originally Posted by Hugh Jardon

Chav!

How rich is that?!!!!!

kitten · 01 June 2011, 20:26

Quote:

Originally Posted by martini

I recently suggested it might be a struggle to fit a blue rizla between the motors but nobody was biting

I dropped a whole packet of greens down beside the port motor, and they haven't been seen since.

As for a lashup comment, I think it went quiet on here as it is frighteningly close to the truth.

The finish on the inside is secret, it gives a good hard wearing nonslip finish and is easily removed with acetone for any repairs or alterations.

Black, if you are waiting by the slip next week to see the first launch, you will be too late.

Mollers · 01 June 2011, 22:20

Quote:

Originally Posted by kitten

As for a lashup comment, I think it went quiet on here as it is frighteningly close to the truth.

Eh?!!

If that's your idea of a lash-up, pull a few panels off of some mass produced cruisers.

That 34 is an awesome bit of kit.

Cookee · 02 June 2011, 08:05

Lack of sense of humour is here - to many long days recently (not as many as Kitten though!)

It is tight in there but it's only a 7'4" beam in the boat!

Steering works now so keep a good look out everybody!

Cookee · 06 June 2011, 08:06

Some good news! We got the boat launched on Friday and although we had a small problem with one of the drives we were happy with the results we have. The boat sits high in the water despite two diesels in the back, it's stable and easy to manoeuvre with the Arnesons.

We did get it onto the plane before the problem but not flat out, so we still don't know the top speed or whether they are the right props for now -

Some photos taken by Tim Tapping who not only took photos but helped with some rigging of the boat and trailer on Friday - thanks Tim!