Serious question on sr4 a frame

[Glenn collins]

Being entirely serious, any pointers as to where I can get An A-frame for my sr4. Or a volunteer to make one at a reasonable cost.

Glenn

[Mollers]

Rescue or deluxe deck?

[Glenn collins]

Originally Posted by Mollers

Rescue or deluxe deck?

Original rescue I think. Stainless transom supports not moulded.

[Mollers]

We had this one fabricated and are really pleased with it. It's now powdercoated orange.

[Glenn collins]

Hi mollers.

Looks super although mine is the wooden transom with two ss tube supports from deck to transom, type of sr4.

Did you make this or have it bashed up for you ??

G

[Downhilldai]

Do you want to tow off it, or just somewhere to fit lights & antenna?

[Glenn collins]

Mounting of lights antenna and life rings no intention of towing

[biffer]

Originally Posted by Downhilldai

Do you want to tow off it, or just somewhere to fit lights & antenna?

i won't tell him if you won't

[Mollers]

Originally Posted by Glenn collins

Hi mollers.

Looks super although mine is the wooden transom with two ss tube supports from deck to transom, type of sr4.

Did you make this or have it bashed up for you ??

G

I had a tame fabricator knock it up. We could knock out more to fit deluxe decked SR4s, but would need a rescue deck at the workshop to get a pattern and dimensions off of it.

[Glenn collins]

Originally Posted by biffer

i won't tell him if you won't

Oh go on ........ PLEASE. :-)

[Downhilldai]

Originally Posted by biffer

i won't tell him if you won't

Originally Posted by Glenn collins

Mounting of lights antenna and life rings no intention of towing

You could get away with a single hoop in that case, which would be easier (& cheaper) to design & fabricate. 1.5" OD stainless or aluminium tube would be ok for this, but 2" would look better (IMHO).

[biffer]

i'll tell you because it will look like bad manners if i don't, i bent some tube up for downhill and i think it was for something like you have, the problem is i have so much work at the moment i couldn't do anything for a couple of months

[Glenn collins]

Originally Posted by Downhilldai

You could get away with a single hoop in that case, which would be easier (& cheaper) to design & fabricate. 1.5" OD stainless or aluminium tube would be ok for this, but 2" would look better (IMHO).

That was what I was really thinking of. There is one on eBay but is to small for outboard to tilt up under.

You would have thought that the amount if little avons still out there some one would be making a killing bashing these out.

Any ideas as to where ?

G

[Glenn collins]

Originally Posted by biffer

i'll tell you because it will look like bad manners if i don't, i bent some tube up for downhill and i think it was for something like you have, the problem is i have so much work at the moment i couldn't do anything for a couple of months

Hi biffer

A couple of months would be better than never.......

Please pm a rough figure and if you would need the boat down there.

G

[biffer]

Originally Posted by Glenn collins

Hi biffer

A couple of months would be better than never.......

Please pm a rough figure and if you would need the boat down there.

G

i'll have a think, i could do a frame with the supports built into it, give us a ring next week with what you would like, 07946 330001

[Downhilldai]

Originally Posted by biffer

i bent some tube up for downhill ..

Very nice it was too

[Glenn collins]

Originally Posted by biffer

i'll have a think, i could do a frame with the supports built into it, give us a ring next week with what you would like, 07946 330001

I'll call you Monday.

G